Filtering PIM-SM Bootstrap Messages
Problem
Your PIM-SM domain uses bootstrap routers to elect RPs. Some of the routers have interfaces that connect to other PIM-SM domains. You need to ensure that Bootstrap messages do not cross the domain boundary.
Solution
On router interfaces that connect to other PIM-SM domains, create filters to prevent bootstrap router messages from crossing domain boundaries:
[edit policy-options] aviva@RouterB# set policy-statement pim-bootstrap-import from interface se-0/0/3 aviva@RouterB# set policy-statement pim-bootstrap-import then reject aviva@RouterB# set policy-statement pim-bootstrap-export from interface se-0/0/3 aviva@RouterB# set policy-statement pim-bootstrap-export then reject [edit protocols pim] aviva@RouterB# set rp bootstrap-import pim-bootstrap-import aviva@RouterB# set rp bootstrap-export pim-bootstrap-export
Discussion
As a final part of the bootstrap router configuration, you need to make sure that Bootstrap messages from one PIM-SM domain don accidentally cross into another PIM-SM domain. To prevent this from happening, configure bootstrap routing-policy filters that reject all incoming and outgoing traffic on interfaces that connect to other PIM-SM domains. The two policies you need to accomplish this are very simple:
aviva@RouterB> show configuration policy-options
policy-statement pim-bootstrap-import {
from interface se-0/0/3.0;
then reject;
}
policy-statement pim-bootstrap-export {
from interface se-0/0/3.0;
then reject;
}
Apply these policies directly in the PIM bootstrap configuration, with the set rp bootstrap-import and set rp bootstrap-export commands in the [edit protocols pim] hierarchy.
See Also
Recipes 9.1 and 16.4
Router Configuration and File Management
- Introduction
- Configuring the Router for the First Time
- Configuring the Router from the CLI
- Getting Exclusive Access to Configure the Router
- Displaying the Commands to Recreate a Configuration
- Including Comments in the Configuration
- Checking the Syntax of the Configuration
- Activating the Router Configuration
- Debugging a Failed Commit
- Exiting Configuration Mode
- Keeping a Record of Configuration Changes
- Determining What Changes You Have Made to the Configuration
- Configuring the Router by Copying a File from a Server
- Configuring the Router by Copying Text from a Terminal Window
- Backing Up the Routers Configuration
- Scheduling the Activation of a Configuration
- Provisionally Activating a Configuration
- Loading a Previous Router Configuration
- Creating an Emergency Rescue Configuration
- Backing Up Filesystems on M-Series and T-Series Routers
- Backing Up Filesystems on J-Series Routers
- Restoring a Backed-Up Filesystem
- Installing a Different Software Release on M-Series and T-Series Routers
- Installing a Different Software Release on J-Series Routers
- Creating an Emergency Boot Disk
- Gathering Software Version Information
- Gathering Hardware Inventory Information
- Finding Out How Long the Router Has Been Up
- Gathering Information Before Contacting Support
- Managing Routers with Similar Configurations
- Managing Redundant Routing Engines
- Using the Second Routing Engine to Upgrade to a New Software Version
Basic Router Security and Access Control
- Basic Router Security and Access Control
- Introduction
- Allowing Access to the Router
- Controlling Root Authentication
- Logging In to the Routers Console
- Setting the Login Authentication Methods
- Setting Up Login Accounts on the Router
- Changing the Format of Plain-Text Passwords
- Changing the Plain-Text Password Encryption Method
- Creating a Login Account for Remote Authentication
- Creating a Group Login Account
- Customizing Account Privileges
- Creating a Privilege Class that Hides Encrypted Passwords
- Setting Up RADIUS User Authentication
- Setting Up TACACS+ User Authentication
- Restricting Inbound SSH and Telnet Access
- Setting the Source Address for Telnet Connections
- Creating a Login Banner
- Finding Out Who Is Logged In to the Router
- Logging Out of the Router
- Forcibly Logging a User Out
IPSec
- IPSec
- Introduction
- Configuring IPSec
- Configuring IPSec Dynamic SAs
- Creating IPSec Dynamic SAs on J-Series Routers or Routers with AS PICs
- Using Digital Certificates to Create Dynamic IPSec SAs
SNMP
- SNMP
- Introduction
- Configuring SNMP
- Setting Router Information for the MIB-II System Group
- Setting Up SNMP Traps
- Controlling SNMP Access to the Router
- Using a Firewall Filter to Protect SNMP Access
- Controlling Access to Router MIBs
- Extracting Software Inventory Information with SNMP
- Extracting Hardware Inventory Information with SNMP
- Collecting Router Operational Information with SNMP
- Logging SNMP Access to the Router
- Logging Enterprise-Specific Traps
- Using RMON Traps to Monitor the Routers Temperature
- Configuring SNMPv3
- Tracking Router Configuration Changes
- Setting Up SNMPv3 Traps
Logging
- Logging
- Introduction
- Turning On Logging
- Limiting the Messages Collected
- Including the Facility and Severity in Messages
- Changing the Size of a Logging File
- Clearing the Routers Logfiles
- Sending Log Messages to Your Screen
- Sending Logging Messages to a Log Server
- Saving Logging Messages to the Other Routing Engine
- Turning Off Logging
- Turning On Basic Tracing
- Monitoring Interface Traffic
NTP
- NTP
- Introduction
- Setting the Date and Time on the Router Manually
- Setting the Time Zone
- Synchronizing Time When the Router Boots
- Synchronizing Time Periodically
- Authenticating NTP
- Checking NTP Status
Router Interfaces
- Router Interfaces
- Introduction
- Viewing Interface Status
- Viewing Traffic Statistics on an Interface
- Setting an IP Address for the Router
- Setting the Routers Source Address
- Configuring an IPv4 Address on an Interface
- Configuring an IPv6 Address on an Interface
- Configuring an ISO Address on an Interface
- Creating an MPLS Protocol Family on a Logical Interface
- Configuring an Interface Description
- Choosing Primary and Preferred Interface Addresses
- Using the Management Interface
- Finding Out What IP Addresses Are Used on the Router
- Configuring Ethernet Interfaces
- Using VRRP on Ethernet Interfaces
- Connecting to an Ethernet Switch
- Configuring T1 Interfaces
- Performing a Loopback Test on a T1 Interface
- Setting Up a BERT Test on a T1 Interface
- Configuring Frame Relay on a T1 Interface
- Configuring a SONET Interface
- Using APS to Protect Against SONET Circuit Failures
- Configuring an ATM Interface
- Dealing with Nonconfigurable Interfaces
- Configuring Interfaces Before the PICs Are Installed
IP Routing
- IP Routing
- Introduction
- Viewing the Routes in the Routing Table
- Viewing Routes to a Particular Prefix
- Viewing Routes Learned from a Specific Protocol
- Displaying the Routes in the Forwarding Table
- Creating Static Routes
- Blackholing Routes
- Filtering Traffic Using Unicast Reverse-Path Forwarding
- Aggregating Routes
- Load-Balancing Traffic Flows
- Adding Martian Addresses
- Changing Route Preferences to Migrate to Another IGP
- Configuring Routing Protocols to Restart Without Losing Adjacencies
Routing Policy and Firewall Filters
- Routing Policy and Firewall Filters
- Introduction
- Creating a Simple Routing Policy
- Changing a Routes Routing Information
- Filtering Routes by IP Address
- Filtering Long Prefixes
- Filtering Unallocated Prefix Blocks
- Creating a Chain of Routing Policies
- Making Sure a Routing Policy Is Functioning Properly
- Creating a Simple Firewall Filter that Matches Packet Contents
- Creating a Firewall Filter that Negates a Match
- Reordering Firewall Terms
- Filtering Traffic Transiting the Router
- Using a Firewall Filter to Count Traffic on an Interface
- Logging the Traffic on an Interface
- Limiting Traffic on an Interface
- Protecting the Local Routing Engine
- Rate-Limiting Traffic Flow to the Routing Engine
- Using Counters to Determine Whether a Router Is Under Attack
RIP
- RIP
- Introduction
- Configuring RIP
- Having RIP Advertise Its Routes
- Configuring RIP for IPv6
- Enabling RIP Authentication
- Routing RIP Traffic over Faster Interfaces
- Sending Version 1 Update Messages
- Tracing RIP Protocol Traffic
IS-IS
- IS-IS
- Introduction
- Configuring IS-IS
- Viewing the IS-IS Link-State Database
- Viewing Routes Learned by IS-IS
- Configuring IS-IS for IPv6
- Configuring a Level 1Only Router
- Controlling DIS Election
- Enabling IS-IS Authentication
- Redistributing Static Routes into IS-IS
- Leaking IS-IS Level 2 Routes into Level 1
- Adjusting IS-IS Link Costs
- Improving IS-IS Convergence Times
- Moving IS-IS Traffic off a Router
- Disabling IS-IS on an Interface
- Tracing IS-IS Protocol Traffic
OSPF
- Introduction
- Configuring OSPF
- Viewing Routes Learned by OSPF
- Viewing the OSPF Link-State Database
- Configuring OSPF for IPv6
- Configuring a Multiarea OSPF Network
- Setting Up Stub Areas
- Creating a Not-So-Stubby Area
- Summarizing Routes in OSPF
- Enabling OSPF Authentication
- Redistributing Static Routes into OSPF
- Adjusting OSPF Link Costs
- Improving OSPF Convergence Times
- Moving OSPF Traffic off a Router
- Disabling OSPF on an Interface
- Tracing OSPF Protocol Traffic
BGP
- Introduction
- Configuring a BGP Session Between Routers in Two ASs
- Configuring BGP on Routers Within an AS
- Diagnosing TCP Session Problems
- Adjusting the Next-Hop Attribute
- Adjusting Local Preference Values
- Removing Private AS Numbers from the AS Path
- Prepending AS Numbers to the AS Path
- Filtering BGP Routes Based on AS Paths
- Restricting the Number of Routes Advertised to a BGP Peer
- Authenticating BGP Peers
- Setting Up Route Reflectors
- Mitigating Route Instabilities with Route Flap Damping
- Adding a BGP Community to Routes
- Load-Balancing BGP Traffic
- Tracing BGP Protocol Traffic
MPLS
- Introduction
- Configuring LSPs Using LDP as the Signaling Protocol
- Viewing Information and LDP-Signaled LSPs in the Routing Tables
- Verifying that an LDP-Signaled LSP Is Carrying Traffic
- Enabling LDP Authentication
- Tracing LDP Operations
- Setting Up RSVP-Signaled LSPs
- Viewing Information About RSVP-Signaled LSPs in the Routing Tables
- Verifying Packet Labels
- Verifying that the RSVP-Signaled LSP Is Carrying Traffic
- Configuring RSVP Authentication
- Protecting an LSPs Path
- Using Fast Reroute to Reduce Packet Loss Following a Link Failure
- Automatically Allocating Bandwidth
- Prioritizing LSPs
- Allowing IGP Traffic to Use an LSP
- Installing LSPs into the Unicast Routing Table
- Tracing RSVP Operations
VPNs
- Introduction
- Setting Up a Simple Layer 3 VPN
- Viewing the VPN Routing Tables
- Adding a VPN for a Second Customer
IP Multicast
- Introduction
- Configuring PIM-SM
- Manually Establishing a PIM-SM RP
- Using Auto-RP to Dynamically Map RPs
- Setting Up a PIM-SM Bootstrap Router
- Filtering PIM-SM Bootstrap Messages
- Configuring Multiple RPs in a PIM-SM Domain with Anycast RP
- Configuring Multiple RPs in a PIM-SM Domain Anycast PIM
- Limiting the Group Ranges an RP Services
- Viewing Multicast Routes
- Checking the Groups for Which a PIM-SM Router Maintains Join State
- Manually Configuring IGMP
- Using SSM
- Connecting PIM-SM Domains Using MSDP and MBGP
- Configuring PIM-DM
- Tracing PIM Packets
Junos Cookbook (Cookbooks (OReilly))
ISBN: 0596100140
EAN: 2147483647
EAN: 2147483647
Year: 2007
Pages: 290
Pages: 290
Authors: Aviva Garrett
