B.8. DVD ProblemsB.8.1. Exporting to iDVD Fails (Error -43)As noted here and there throughout this book, you can extend iMovie's effects, transitions, and title styles by installing plug-ins from other companies. If you haven't updated your plug-ins to iMovie HDspecific versions, you've found the problem; they can prevent you from exporting to iDVD. B.8.2. Video and Audio Aren't In SyncOn some longer movie projects (20 minutes or more), everything plays fine in iMovie, but when you turn your project into a QuickTime movie or burn it to a DVD, the audio and video grow slowly, horrifyingly out of sync. The longer the movie plays, the farther apart they drift . The most important thing to check is the audio recording settings of your camcorder. As described at the beginning of this chapter, most camcorders come set to record 12-bit audio, which lies at the heart of the video/audio drift problem. Change it to 16-bit audio, using the camcorder's own menus . (If you use a video converter like the Formac Studio or Dazzle Hollywood Bridge, make sure it, too, is set to import 16-bit audio, not 12-bit.) If it's too late for that step, here are two possible fixes. B.8.2.1 The back-to-camcorder solutionSet your camcorder to 16-bit audio. Once editing is complete, export the entire movie to your camcorder (see Chapter 11). Then start a new iMovie project file and import the camcorder's footage right back into your Mac (Chapter 4). This time, you should be able to export the project without the drift. B.8.2.2 The export-as-QuickTime solutionFor this trick, you'll export the project as a high-quality QuickTime movie. Chapter 12 offers details on exporting iMovie projects as QuickTime movies. For this particular task, though, these steps guide you through the proper settings:
B.8.3. White Frames at Chapter Markers in SlideshowsYou've created a gorgeous slideshow in iMovie. You've added chapter markers to help your audience navigate. And you've burned it to a DVDand you've cringed at the blinks of white that appear at each chapter marker. The workaround: don't put chapter markers in your main project file. Instead, once your movie is otherwise ready, export it as a Full Quality QuickTime movie. (Choose File Share, click the QuickTime button, choose Full Quality from the pop-up menu, click Share. Use any name and folder location.) Import the exported movie into a new iMovie HD Project, and add chapter markers at this stage. Finally, export to iDVD and burn your disc as usual. B.8.4. Photos Look Jaggy and Awful on DVDAll over the world, every single day, more Mac fans try to turn their digital photos into DVD slideshows using iMovieand find out that the photos look terrible. What makes this syndrome so baffling is that the photos probably began life with super high resolution and look fantastic in Photoshop or iPhoto. But once they arrive on a DVD, the pictures look lousy. It turns out that when you click the Create iDVD Project button in iMovie (the usual way to hand off the project to iDVD), iMovie offers to process any still photosto render them, turning them into what amounts to motionless video. "Your movie contains still, slow motion, and/or reverse clips," it says. If you click "Render and Proceed," iMovie does a pretty poor job at converting them into video, resulting in jaggy blockiness. (This conversion is permanent in iMovie. Once it's done, your photos will always look bad in iMovie until you reinsert the originals .) The solution is to bypass iMovie's low-quality photo-rendering cycle altogether. You can do that in either of two ways. B.8.4.1 The Ken Burns MethodIf you turn your photos into digital video clips, then iMovie doesn't consider them stills any more, and won't attempt to render them. Here's how to do that: Turn on the Ken Burns Effect checkbox (page 251), configure the pan or zoom settings, then import the image. After the bright red progress bar finishes its trip across your photo clip, you're left with a very high quality "still" video clip that iMovie won't attempt to process when you hand off to iDVD. Repeat this process for any other still photos in your movie. At this point, your still photos are no longer still photos. Clicking the "Create iDVD Project" button is now safe. iMovie will make no attempt to render your stills, because they've already been rendered by the far superior Ken Burns feature. B.8.4.2 The Drag-into-iDVD MethodThe second way to bypass iMovie's still-photo rendering feature is to avoid the "Create iDVD Project" button altogether. As you may remember from Chapter 16, there's another way to bring an iMovie movie into iDVD: drag its title-bar icon right into the iDVD window. See page 391 for the proper technique. If you do that, iMovie's weak photo-rendering software doesn't touch your stillsand iDVD's own, much better rendering software processes them instead. You may find that the Ken Burns technique looks slightly better on some photos, but of course, it's much more work than the drag-into-iDVD method. Either way, though, you'll be delighted with the results. At disc-burning time, iDVD will perform the photo processing itself, with much better results. |