Basic Phone Services and Circuits

team lib

Here's how to go the last mile with the phone company.

Telephone company offerings are complex. Unless we have corporate responsibility for provisioning voice or data telecommunications services from the telephone company, most of us rarely have any involvement with telephone lines aside from the analog local loop that provides the voice services that allow telemarketers to call us during dinner.

While telephone company offerings can be really hard to understand and to distinguish between, even that is easy in comparison to understanding their costs. This tutorial can't begin to tackle the cost issue, but it will try to make the relevant distinctions among some of the more frequently encountered products and services available from telephone service providers.

Analog Lines, Digital Lines

The first important distinction is between analog and digital lines. Analog signals vary continuously, and they represent particular values, such as the volume and pitch of a voice or the color and brightness of a section of an image. Digital signals have meaning only at discrete levelsin the most common case, the signal is either on or off, present or absent, 1 or 0.

Analog telephone lines are the legacy systems of the telephone universe. The great preponderance of residential telephone lines is analog. Fifty-year-old telephones will probably work on your local loopthe connection between your home telephone jack and the telephone company's central office. (Your central office is probably not a gigantic building downtownthe average local loop is about 2.5 miles long [four kilometers], so the "central office" is most often an inconspicuous building in or near your neighborhood.)

When you talk on the telephone, the microphone in the "receiver" (while you're talking, it's actually a transmitter) produces an analog signal that travels to the central office and is switched either to another local destination or to other switching offices that connect it to a remote destination. Dialing the telephone produces the in- band signals that tell the switching system where to route the call. The telephone companies have learned a great deal about the electrical characteristics of human voice signals over the years , and they have determined that we will be reasonably satisfied with voice signals that do not transmit frequencies below 300Hz or above 3,100Hz. Note that high fidelity is usually considered to be a system that can reproduce frequencies between 20Hz and 20KHz without distortion. While voices are recognizable with the standard telephone frequency range, that range of frequencies is likely to be inadequate for other types of soundsfor instance, music sounds lousy over the telephone. To allow for gradual rolloffs of high and low frequencies, the telephone companies allow an analog telephone channel a bandwidth of 4,000Hz to work with.

At the central office, the odds are that the analog signal will be digitized in order to be switched across the telephone network. Aside from Giblet County, AK, and Rat Fork, WY, the U.S. telephone network that interconnects central offices uses digital signaling. Although many urban business telephone users have digital services direct to their PBXs or data communication devices, and ISDN lines are digital, the local loop is sometimes referred to as "the last mile," because residences, generally saddled with analog-only transmission facilities, were traditionally limited to the 4,000Hz bandwidth that dial-up modems can use.

What can 4khz do?

Modems convert digital signals from a computer into analog signals in the telephone frequency range. There is a hard upper limit to the capacity of a channel with a given bandwidth. A channel's throughput in bits per second depends on the bandwidth and the achievable signal-to-noise ratio. The current top throughput rate for modems of 33.6Kbits/sec is quite close to the limit. As users of 28.8Kbit/sec modems know, the actual throughput achievable on normally noisy analog lines is rarely the full-rated value, and it may be much lower. Compression and caching and other tricks can mask the limit to an extent, but we'll see perpetual motion machines before we see a classically defined modem with, say, 50Kbits/sec or even 40Kbits/sec throughput on ordinary analog telephone lines. The near-56Kbit/sec V.90 modem doesn't actually send modulated analog signals like other modems do. Instead, it transmits a "raw" digital signal in the downstream direction, avoiding the quantization noise that would be created by a digital-to-analog conversion.

When the telephone company reverses the process and digitizes an analog voice signal, it uses a 64Kbit/sec channel. (This conversion is a worldwide standard.) One of these channels, called a DS0 (digital signal, level zero), is the basic building block for telephone processes. You can agglomerate (the precise term is multiplex ) 24 DS0s into a DS1. If you lease a T1 line, you get a DS1 channel. With synchronization bits after each 192 bits (that is, 8,000 times a second), the DS1 capacity is 1.544Mbits/sec (the product of 24 and 64,000, added to 8,000).

Dedicated Lines, Switched Lines

The second important distinction to make about telephone lines is whether they are dedicated circuits you lease or switched services you buy. If you order a T1 line or a low data-rate leased line such as dataphone digital service (DDS), you are renting a point-to-point facility from the telephone company. You have dedicated use of such a circuit-with 1.544Mbits/sec (T1) or 56Kbits/sec (low data rate) of capacity, respectively.

While frame relay services are switched through a cloud frame by frame, they are almost invariably sold as permanent virtual circuits, where the customer specifies the end points. For purposes of designing a network layout, frame relay links have more in common with dedicated lines than with switched lines, but the cost can be substantially lower for an equivalent capacity. Switched services, such as residential analog telephone service, are services purchased from the telephone company. You can select any destination on the telephone network and connect to it through the network of public switches. You generally pay for connect time or actual traffic volume, so unlike a dedicated line, the bill will be low if usage is low. Switched digital services include X.25, Switched 56, ISDN Basic Rate Interface (BRI), ISDN Primary Rate Interface (PRI), Switched Multimegabit Data Service (SMDS), and ATM. It's also possible to set up private networks that supply these services using your own switching equipment and leased lines or even privately owned linesfor example, if you are a university, a railroad , or a municipal utility.

If the circuit provided by the phone company is already a digital circuit, there is no need for a modem to provide digital-to-analog conversion services between the terminal equipment (phone company talk for such equipment as computers, fax machines, videophones, and digital telephone instruments) and the telephone system. Nonetheless, customer premises equipment still needs to behave like a good citizen of the telephony network. In particular, it must present the correct electrical termination to the local loop, transmit traffic properly, and support phone company diagnostic procedures.

A line that supports ISDN BRI service must be connected to a device called an NT1 (network termination 1). In addition to the line termination and diagnostic functions, the NT1 interface converts the two-wire local loop to the four-wire system used by digital terminal equipment. For digital leased linesT1 and DDSand for the digital services, the digital subscriber line from the phone company needs to be terminated by a channel service unit or CSU. The CSU terminates and conditions the line and responds to diagnostic commands. Customer terminal equipment is designed to interface with a data service unit (DSU), which hands over properly formatted digital signals to the CSU. CSUs and DSUs are often combined into a single unita CSU/DSU, of all things. The DSU may be built into a router or multiplexer. So even though end-to-end digital services don't require modems, a piece or two of interfacing hardware is always required for connectivity.

Media For Phone Services

While 33.6Kbits/sec is a stretch for most local loops configured for analog service, the same twisted-pair wiring running between your house and a central office is very likely capable of supplying ISDN BRI service, with 128Kbits/sec of data throughput capacity and another 16Kbits/sec of control and setup capacity. How is this possible? Analog telephone circuits are heavily filtered to keep the signals attenuated outside their 4KHz bandwidth because 4KHz is the highest frequency a DSO can handle. Digital circuits don't need to be filtered the same way, so the twisted pair cable can support a much greater bandwidth, which allows greater throughput.

Leased 56Kbit/sec and 64Kbit/sec lines and services that run on these lines, such as frame relay and Switched 56, may be delivered on a two-wire digital line or on a four-wire digital line (which has separate wire pairs for transmitting and receiving). T1 lines as well as ISDN PRI and frame relay are often delivered on four-wire digital lines or perhaps on optical fiber. T3 lines are sometimes coaxial cable, but most high-capacity traffic is carried on optical fiber. While ISDN is getting a lot of attention as a high-capacity, wide-area connection, it is not the last word on throughput for the "last mile." PairGain (Tustin, CA) and AT&T Paradyne (Largo, FL) market products using Bellcore's (Piscataway, NJ) high bit-rate digital subscriber loop (HDSL) technology. These products serve to equalize local loops dynamically, making it possible to support DS1 throughput1.544Mbits/secover most existing twisted pair local loops, provided that HDSL devices are installed at both ends. (With standard 24-gauge wire, HDSL can be used successfully on local loops up to 2.3 miles long, with no repeaters. Ordinary T1 circuits require repeaters at least every 3,000 feet to 5,000 feet.) If you want to transport DS1 levels of traffic over the last mile, the alternatives to HDSL are to install "fiber to the curb" at great expense or to install several repeaters on each line, which is not as expensive as all-new fiber but is still costly and imposes a large maintenance cost on the telephone company (and, ultimately, on the customer).

Table 1: Telephone Service Types

Circuit type

Service

Switched service

Local loop transmission medium

Analog

POTS

Circuit switched

Two-wire twisted pair

DS0 (64Kbits/sec)

DDS (leased line)

Dedicated line

Two-wire or four-wire twisted pair

 

Frame relay

Packet-switched PVC

Two-wire or four-wire twisted pair

 

X.25

Packet switched

Two-wire or four-wire twisted pair

 

Switched 56

Circuit switched

Two-wire or four-wire twisted pair

 

Switched 64

Circuit switched

Two-wire or four-wire twisted pair

 

ISDN BRI

Circuit switched

Two-wire twisted pair

Multiple DS0 (between 64Kbits/sec and 1.536Mbits/sec in 64Kbits/sec increments )

Fractional T1

Dedicated line

Two-wire or four-wire twisted pair

 

Frame relay

Packet-switched PVC

Two-wire or four-wire twisted pair

DS1 (1.544Mbits/sec) (24 DS0s)

T1 leased line

Dedicated line

Four-wire twisted pair or fiber

 

Frame relay

Packet-switched PVC

Four-wire twisted pair or fiber

 

SMDS

Packet switched

Four-wire twisted pair or fiber

 

ISDN PRI

Circuit switched

Four-wire twisted pair or fiber

DS3 (44.736Mbits/sec) (28 DS1s, 672 DS0s)

T3 leased line

Dedicated line

Coax or fiber

 

ATM

Cell switched

Coax or fiber

 

SMDS

Packet switched

Coax or fiber

HDSL is not even the final word on improving the throughput of the last mile. Asymmetrical digital subscriber line technology (ADSL) supports throughput as high as 8Mbits/sec in a single direction, with a much lower throughputperhaps as low as 64Kbits/secin the other direction. In a perfector at least competitiveworld, where customers pay for a telephone service based on the actual cost of delivering that service, a high percentage of analog telephone customers could receive ISDN PRI (or another T1 service) at a price comparable to today's cost for ISDN BRI.

But, perhaps today's ISDN promoters don't have much to worry about. In most cases, telephone companies can install these special line equalizers and keep the savings to themselves . As is so often the case with tariffed services, there's no requirement that the rates be rational.

This tutorial, number 89, by Steve Steinke, was first published in the January 1996 issue of LAN Magazine/Network Magazine.

 
team lib


Network Tutorial
Lan Tutorial With Glossary of Terms: A Complete Introduction to Local Area Networks (Lan Networking Library)
ISBN: 0879303794
EAN: 2147483647
Year: 2003
Pages: 193

flylib.com © 2008-2017.
If you may any questions please contact us: flylib@qtcs.net