Question 1 | Which of the following commands would provide an administrator with a list of known Novell servers on the network? -
A. debug ipx ipxwan -
B. show ipx servers -
C. show ipx traffic -
D. show ipx all |
A1: | Answer: B. The show ipx servers command would show all the known servers in the network. |
Question 2 | Which of the following commands was used to produce this output? IPX EIGRP Topology Table for process 20 Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - Reply status P A, 1 successors, FD is 342217 via 20.0060.3a7b.ab21 (342217/307200), s0 P D, 1 successors, FD is 152221 via Connected, s1 |
A2: | Answer: A. This output is from the show ipx eigrp topology command. The first line indicates the table. | You can expect the exam to have obvious questions just like Question 2. | |
Question 3 | An IPX extended access list can filter based on which of the following? |
A3: | Answer: E. All the items listed are valid criteria for filtering with an extended IPX access list. |
Question 4 | Which of the following number ranges can be used to number an IPX standard access list? -
A. 1-99 -
B. 800-899 -
C. 900-999 -
D. 1000-1099 |
A4: | Answer: B. The valid range of numbers for an IPX standard access list is 800-899. |
Question 5 | Which of the following is the default encapsulation type for Novell NetWare 5.0 or 6.0 clients and servers? -
A. ARPA -
B. Ethernet_II -
C. NOVELL-ETHER -
D. Ethernet_802.3 -
E. None of the above |
A5: | Answer: E . IP is the default for Novell clients and servers running NetWare 5.0 and 6.0, so an encapsulation type would not be needed. Options C and D would be correct for the default encapsulation type for Novell clients and servers that are not running NetWare 5.0 or later. |
Question 6 | A Novell client is using Ethernet II. Which of the following frame types can be used? [Choose the two best answers.] -
A. Ethernet II -
B. 802.3 -
C. ARPA -
D. 802.5 |
A6: | Answers: A, B . This is a trick question. Ethernet II and ARPA are the same thing. You need to remember that Novell calls the encapsulation type Ethernet II and Cisco calls it ARPA, so both answers are correct. |
Question 7 | Which of the following is a valid IPX network address? |
A7: | Answer: A . An IPX address requires four octets in hexadecimal format that specify both the network and the node. |
Question 8 | By default, SAP packets are sent how often? |
A8: | Answer: C . The default setting for SAP packet advertisements is 60 seconds. |
Question 9 | What is the maximum number of hops supported by IPX RIP? -
A. 7 -
B. 15 -
C. 64 -
D. Unlimited |
A9: | Answer: B . IPX RIP has the same hop count maximum as IP RIP, which is 15. This means that no more than 15 routers can exist between any two given points in the network. |
Question 10 | Which of the following commands was used to display this output? S/0 is up, line protocol is up IPX address is 20.0060.1a30.289a [up] line-up, RIPPQ: 0, SAPPQ: 0 Delay of this IPX network, in ticks is 1 throughput 0 link delay 0 IPXWAN processing not enabled on this interface. IPX SAP update interval is 1 minute(s) IPX type 20 propagation packet forwarding is disabled Incoming access list is not set Outgoing access list is not set IPX helper access list is not set SAP GNS processing enabled, delay 0 ms, output filter list is not set SAP Input filter list is not set SAP Output filter list is not set SAP Router filter list is not set Input filter list is not set Output filter list is not set Router filter list is not set |
A10: | Answer: C . The show ipx interface s0 command was used to produce the output. |