1-1 router ospf process-id

1-1 router ospf process-id

Syntax Description:

• process-id ” The OSPF process ID. The range of values is 1 to 65535.

Purpose: Used to enable one or more OSPF processes on a router. The process ID is only significant on the local router. Use the no form of the command to remove an OSPF process.

Initial IOS Software Release: 10.0

Configuration Example: Enabling an OSPF Process

Before you enable an OSPF process, there must be at least one active interface with an assigned IP address. OSPF uses the highest IP address assigned to an active interface as the OSPF Router ID. If loopback interfaces have been configured, then OSPF will use the highest loopback address as the Router ID even if the highest loopback IP address is smaller than the IP address of any active physical interface. Using a loopback interface on an OSPF router is recommended because a loopback interface is never down. A loopback interface will produce a stable OSPF router ID. The network in Figure 1-1 demonstrates that the OSPF Router ID (RID) is the highest IP address assigned to an active physical interface. If a loopback interface is used, then OSPF will use the loopback IP address as the OSPF RID.

Figure 1-1. OSPF Router ID Selection

Start by removing all IP addresses and loopback interfaces from Router B. Now, attempt to configure an OSPF process on Router B.

 rtrB#  configure terminal  Enter configuration commands, one per line.  End with CNTL/Z. rtrB(config)#  router ospf 1  OSPF: Could not allocate router id 

OSPF cannot be enabled on Router B because OSPF needs a RID and there are no IP addresses assigned on Router B. Configure the serial interfaces on Routers A and B and then configure an OSPF process on Router B.

 Router A  interface Serial0/1   bandwidth 64   ip address 10.1.1.1 255.255.255.252   clockrate 64000  _______________________________________________________________________ Router B  interface Serial0   ip address 10.1.1.2 255.255.255.252   bandwidth 64   router ospf 1  

The configuration of the OSPF process on Router B was successful. Examine the OSPF RID on Router B using the show ip ospf command.

 rtrB#  show ip ospf  Routing Process "ospf 1" with  ID 10.1.1.2  Supports only single TOS(TOS0) routes  SPF schedule delay 5 secs, Hold time between two SPFs 10 secs  Number of DCbitless external LSA 0  Number of DoNotAge external LSA 0  Number of areas in this router is 0. 0 normal 0 stub 0 nssa 

The only active interface on Router B is Serial0, so OSPF will use the IP address assigned to Serial0 for the router ID. Add a loopback interface to Router B and then re-examine the OSPF RID on Router B.

 Router B  interface Loopback0   ip address 2.2.2.2 255.255.255.255  rtrB#  show ip ospf  Routing Process "ospf 1" with  ID 10.1.1.2  Supports only single TOS(TOS0) routes  SPF schedule delay 5 secs, Hold time between two SPFs 10 secs  Number of DCbitless external LSA 0  Number of DoNotAge external LSA 0  Number of areas in this router is 0. 0 normal 0 stub 0 nssa 

The OSPF RID has not changed. This is a stability feature of OSPF. The router ID will not change unless the OSPF process is restarted or if the interface used for the RID goes down. Shut down the serial interface on Router B, re-enable the serial interface on Router B, and examine the effect on the OSPF RID.

Verification

Verify that the OSPF RID on Router B is equal to the IP address assigned to the loopback interface.

 rtrB#  show ip ospf  Routing Process "ospf 1" with  ID 2.2.2.2  Supports only single TOS(TOS0) routes  SPF schedule delay 5 secs, Hold time between two SPFs 10 secs  Number of DCbitless external LSA 0  Number of DoNotAge external LSA 0  Number of areas in this router is 0. 0 normal 0 stub 0 nssa 

Troubleshooting

Verify that a loopback interface has been configured and an IP address assigned before configuring OSPF. A loopback interface is not mandatory, but it will add stability to your OSPF network.