Hack 2 802.11a: The Betamax of the 802.11 Family

figs/beginner.giffigs/hack02.gif

802.11a offers more channels, higher speed, and less interference than other protocols, but it still just isn't popular.

According to the specifications available from the IEEE (at http://standards.ieee.org/getieee802/), both 802.11a and 802.11b were ratified on September 16, 1999. Early on, 802.11a was widely touted as the "802.11b killer," as it not only provides significantly faster data rates (up to 54 Mbps raw, or about 27 Mbps actual data), but also operates in a completely different spectrum the 5 GHz UNII band. It uses an encoding technique called Orthogonal Frequency Division Multiplexing (OFDM).

While the promises of higher speeds and freedom from interference with 2.4 GHz devices made 802.11a sound promising, it came to market much later than 802.11b. It also suffers from range problems: at the same power and gain, signals at 5 GHz appear to travel only half as far as signals at 2.4 GHz, presenting a real technical hurdle for designers and implementers. The rapid adoption of 802.11b only made matters worse, since users of 802.11b gear didn't have a clear upgrade path to 802.11a (as the two are not compatible). As a result, 802.11a still isn't nearly as ubiquitous or inexpensive as 802.11b, although client cards and dual-band access points (which essentially incorporate two radios, or a single radio with a dual-band chipset) are coming down in price.

Pros

  • Very fast data rates: up to 54 Mbps (raw radio rate), with some vendors providing 72 Mbps or faster with proprietary extensions.

  • Uses the much less cluttered (for now, in the U.S.) UNII band, at 5.8 GHz.

Cons

  • As of this writing, 802.11a equipment is still more expensive on average than 802.11b or 802.11g.

  • Most 802.11a client devices are add-on cards, and the technology is built into relatively few consumer devices (specifically laptops).

  • 802.11a PCMCIA cards require a 32-bit CardBus slot, and won't work in older devices.

  • Cards and APs with external antenna connectors are hard to find, making distance work difficult.

  • Upgrading from 802.11b can be painful, as 5.8 GHz radiates very differently from 2.4 GHz, requiring a new site survey and likely more APs.

  • Limited range compared to 802.11b and 802.11g, at the same power levels and gain.

  • Internal 802.11a antennas tend to be quite directional, making them sometimes annoyingly sensitive to proper orientation for best results.

Recommendation

The Wi-Fi alliance (http://www.weca.net/) tried to call 802.11a "Wi-Fi5," but the name never stuck. These devices are also sometimes confusingly labeled "Wi-Fi," just like the completely incompatible 802.11b. Be sure to look for the specification's real name (802.11a) when purchasing gear.

802.11a can be significantly faster than 802.11b, but achieves roughly the same throughput as 802.11g (27 Mbps for 802.11a, compared to 20-25 Mbps for 802.11g). 802.11a would be ideal for creating point-to-point links, if devices with external antenna connectors were more readily available. Many people tout OFDM's ability to cope with reflections caused by obstacles (called multipath) as a good reason to use 802.11a, but 802.11g uses the same encoding while achieving greater range at the same power and gain. Some consider the shorter range of 802.11a to be a security advantage, but this can lead to a false sense of security. See the introduction to Chapter 6, as well as [Hack #81] for more details.

Keep in mind that the 54 Mbps data rate is the theoretical maximum, and frequently is only achieved when in very close proximity to the AP. The speed scales back sharply as your distance from the AP increases, and suffers dramatically when separated by a wall or other solid obstacle. It is a very good idea to perform a site survey complete with throughput testing to determine whether 802.11a is suitable for your intended location.

It is probably a bad idea to build an 802.11a-only network unless you are already committed to using only 802.11a gear. If you want to allow guests to use your network, it is a very good idea to at least incorporate a few dual-band APs (or perhaps a dedicated 802.11g AP), as guest users are more likely to bring 802.11b or 802.11g gear with them.



Wireless Hacks. 100 Industrial-Strength Tips and Techniques
Wireless Hacks. 100 Industrial-Strength Tips and Techniques
ISBN: N/A
EAN: N/A
Year: 2003
Pages: 158

flylib.com © 2008-2017.
If you may any questions please contact us: flylib@qtcs.net