Configure the Frame Relay portion of the network as shown in Figure 5-8 and ensure that only the PVCs illustrated in Figure 5-8 will be used. Use of dynamic PVCs is not permitted.
Figure 5-8. Frame Relay Diagram
You must use subinterfaces on R2 interface s0/1.
Do not configure subinterfaces on any other routers.
You must be able to ping across the Frame Relay cloud.
Section 1.2: 3550 LAN Switch Configuration (12 Points)
Sw1 and Sw2 are connected via a crossover cable using ports fa0/15. Configure a Dot1q (801.1Q) trunk between Sw1 and Sw2.
All Ethernet ports are pre-cabled as per Table 5-4. Note that not all ports will be used on this lab.
Table 5-4. 3550 Cabling Guide
Interface
Switch-1
Switch-2
R1 e0/0 (2611)
fa0/1
-
R1 e0/1(2611)
-
fa0/1
R2 fa0/0 (3725)
Fa0/2
-
R2 fa0/1 (3725)
-
fa0/2
R3 fa0/0 (2621)
fa0/3
-
R3 fa0/1(2621)
-
fa0/3
R4 e0/0 (3640)
fa0/4
-
R5 fa0/0 (2621)
fa0/5
-
R5 fa0/1(2621)
-
fa0/5
R6 e0/0 (3640)
fa0/6
-
R6 fa1/0 (3640)
-
fa0/6
Backbone 1
fa0/13
-
Backbone 2
-
fa0/13
Trunk
fa0/15
fa0/15
Trunk
fa0/17
fa0/17
Configure the VLANs as follows:
- VLAN_11: Connected to R1-e0/0 (VLAN_11)
- VLAN_22: Connected to R3-fa0/0, R5-fa0/0, and R6-e0/0 (VLAN_22)
- VLAN_25: Connected to R1-e0/1 and R5-fa0/1 (VLAN_25)
- VLAN_33: Connected to R3-fa0/1 (VLAN_33)
- VLAN_100: Connected to R2-fa0/0 and BB1_Router-e2/0 (VLAN_100)
- VLAN_200: Connected to R4-e0/0 and BB2_Router-e2/4 (VLAN_200)
Configure Sw1 to be the VTP server for the domain. Sw2 is a VTP client. Be sure that Sw2 can see the VLAN configuration from Sw1. The VTP domain name is "CCIE."
Configure Sw1, using VLAN_11 with the IP address 160.10.11.10/24. After you have finished all tasks related to the IGP section, all routers on your topology should be able to ping Sw1 VLAN_11 interface. R1 should also be able to ping this interface. Sw1 will not participate on the IP routing.
You are planning to connect your Sw2 to an external network and you are concerned about sending some of your network information through this port. Configure Sw2-fa0/18 to not send CDP advertisements to the remote side.
Section 1.3: ATM Configuration (3 Points)
Configure the ATM connection as shown in Figure 5-9.
Figure 5-9. ATM Diagram
A PVC is configured between R6 and the backbone router. Do not configure subinterfaces.
Use explicit address mapping. Do not depend on the remoter backbone router for inverse ARP.
You must be able to ping the backbone router address 170.100.10.254.