error
All versions of sendmail define a special internal delivery agent called error that is designed to aid in the issuance of error messages. It is always available for use in the parse rule set 0, the localaddr rule set 5, and the Local_check and other policy setting rule sets. It cannot be defined with an M command. Beginning with V8.7, the form for using the error agent in the RHS of a rule looks like this: R... $#error $@ dsnstat $: text of error message here In general terms, the text following the $ : is the actual error message that will be included in bounced mail and sent back to a connecting SMTP host. For example, the following rule in the parse rule set 0 would cause all mail to the local user George Washington to bounce: RGeorge.Washington $#error 5.1.1 $: 553 George doesn't sleep here anymore with an error message such as this: 553 5.1.1 <george.washington>... George doesn't sleep here anymore The $@ dsnstat part when used with the error delivery agentDelivery Status Notification (DSN, see RFC1893) provides a means for conveying the status of a message's delivery. That status is conveyed in the form of a three-part numeric expression (so as to be easily parsed by machines). This expression is included in the "machine-readable" part of bounced messages: success.category.detail Each part is separated from the others with dot characters . There can be no space around the dots. The parts are numeric, and the meanings are as follows :
The $@ part of the error delivery agent declaration specifies a DSN code that is appropriate for the error: R... $#error $@ success.category.detail $: text of error message here The sendmail program sets its exit (2) value according to the success.category.detail specified. Table 20-4 shows the relationship between those DSN codes on the left and Unix exit (2) values on the right. Note that the exit values are defined in <sysexits.h >, and note that success codes of 2 and 4 completely ignore any category and detail that might be present (that is, 2. anything . anything marks successful delivery, and 4. anything . anything marks a temporary failure). If $@ lists a code that is not in the table, the default exit value is EX_CONFIG. To illustrate , observe that 5.7.1 (see RFC1893) will exit with EX_DATAERR because it corresponds to the *.7.* in the table. Table 20-4. DSN versus exit(2) values with $@ of $#error
To illustrate, consider the need to reject all mail from a particular host (say, evilhost.domain ). We want to reject that host for security reasons, so we might set up a rule such as this: R$* < @ evilhost.domain > $* $#error $@ 5.7.1 $: You are bad, go away Here, the number following the $@ contains a dot, so it is interpreted as a DSN status expression. The .7. causes sendmail to set its exit value to EX_DATAERR. The 5.7.1 is defined in RFC1893 as meaning "Permanent failure, delivery not authorized, message refused ." If the number following the $@ does not contain a dot, sendmail sets its exit (2) value to that number. For example, the following code results in the same exit (2) value as the preceding code but gives a less informative DSN status line in the bounce message: R$* < @ evilhost.domain > $* $#error $@ 65 $: You are bad, go away If the expression following the $@ is nonnumeric, sendmail looks up the string and translates any string it recognizes into the appropriate exit (2) value. The recognized strings are listed in the third column of Table 20-4. For example, the following will cause sendmail to exit with an EX_UNAVAILABLE value: R$* < @ evilhost.domain > $* $#error $@ unavailable $: You are bad, go away If the string following the $@ is not one of those listed in the table, the default exit (2) value becomes EX_UNAVAILABLE. The $: part when used with the error delivery agentRecall that the text of the error message following the $ : is used as a literal error message. That is, this $ : part: R... $#error $@ 5.0.0 $: george doesn't sleep here anymore produces this error for the address george@wash.dc.gov : 553 5.0.0 <george@wash.dc.gov>... george doesn't sleep here anymore Here the 553 is an SMTP code (see RFC821). If you want a different SMTP code issued, you can do so by prefixing the $ : part with it, as shown: R... $#error $: 450 george doesn't sleep here anymore If three digits followed by a space are present as a prefix, those digits are used as the SMTP reply code when sendmail is speaking SMTP. If no digits and space prefix the text, the default SMTP reply code is 553. A few SMTP codes that are useful with $ : are listed in Table 20-5. The complete list of all SMTP codes can be found in RFC2821. Table 20-5. SMTP codes useful with $:
Note that you should restrict yourself to the small set of codes that can legally be returned to the RCPT SMTP command. Also note that any DSN status expression that is specified in the $@ part must avoid conflicting with the meaning of the SMTP code. For example, the following construct is wrong and should be avoided: R... $#error $@ 2.1.1 $: 553 ... Here, the DSN 2.1.1 means that delivery was successful, whereas the SMTP 553 means that delivery failed and the message bounced. In general, the first digit of the SMTP code should match the first digit of the DSN status expression. |
the value of EX_DATAERR from <sysexits.h > 
avoid such conflicts 
EAN: 2147483647
Pages: 1174