Digital Subscriber Line

Digital subscriber line (DSL) technology is a modem technology using existing twisted-pair telephone lines to carry high-bandwidth applications, such as multimedia and video. The term xDSL covers a number of DSL technologies, such as Asymmetrical Digital Subscriber Line (ADSL), Symmetrical Digital Subscriber Line (SDSL), Hi-Speed Digital Subscriber Line (HDSL), HDSL-2 (HDSLv2), ITU DSL standard (G.SHDSL), ISDN Digital Subscriber Line (IDSL), and Very-High-Data-Rate Digital Subscriber Line (VDSL).

xDSL services are dedicated point-to-point network access over twisted-pair copper wire on the local loop (last mile) between a network service provider's (NSP) central office (CO) and the customer site. xDSL also can be deployed in intra-building and intra-campus environments, as illustrated in Figure 7-1.

Figure 7-1. Intra-Building and Intra-Campus/Inter-Building

graphics/07fig01.gif

xDSL offers two chief benefits over dial-up service:

  • Dial-up service is limited to 53.3 Kbps, whereas xDSL service can enable up to 6.122 Mbps.

  • Dial-up service is initiated "on-demand" by the end-user, but xDSL service is a dedicated connection, meaning that it is "always on."

The following sections discuss ADSL. ADSL is often deployed in the small office/home office (SOHO) environment and is the traditional DSL service for residential deployment. The asymmetry is ideal in these environments because the majority of upstream bandwidth is consumed by Internet requests; for example, users navigating through web sites. These upstream requests are small compared to the downstream response, such as the web site fulfilling the user's request.

ADSL

ADSL technology makes more bandwidth available downstream, from a NSP central office (CO) to the customer site, than it makes available upstream, from the customer site to the CO. Figure 7-2 illustrates an example of an ADSL connection.

Figure 7-2. ADSL Connection

graphics/07fig02.gif

The asymmetry of ADSL, combined with always-on access (which eliminates call setup), makes ADSL another solution for Internet/intranet surfing, video-on-demand, and remote LAN access because users of these applications often download more data than they upload.

ADSL Architecture

ADSL circuits connect ADSL modems on each end of a twisted-pair telephone line, creating three data channels:

  • A high-speed downstream channel Ranges from 1.5 to 9 Mbps.

  • A low-speed upstream channel Ranges from 16 to 640 Kbps.

  • A basic telephone service channel The basic telephone service channel is split off from the digital modem by filters or plain old telephone service (POTS) splitters, providing uninterrupted basic telephone service.

NOTE

The upstream and downstream bandwidth ranges depend upon the distance between the customer site and the DSL provider's CO; the greater the distance, the lower the bandwidth capacity.

Figure 7-3 illustrates the architecture of an ADSL network.

Figure 7-3. ADSL Architecture

graphics/07fig03.gif

ADSL architecture is made up of the following components:

  • Transport System Provides the carrier backbone transmission interface for the DSLAM system. This device can provide service specific interfaces such as T1/E1, T3/E3, OC-1/3, and STS-1/3.

  • Local Access Network Uses the local carrier Inter-CO network as a foundation, providing connectivity between multiple service providers and multiple services users, often with Frame Relay or ATM switches.

  • Digital Subscriber Line Access Multiplexer (DSLAM) Concentrates data traffic from multiple DSL loops onto the backbone network for connection to the rest of the network.

  • DSL Transceiver Unit- Remote (xTU-R) The customer site equipment for service connection to the DSL loop.

  • POTS Splitters Optional device at both CO and service user locations, enabling the copper loop to be used for simultaneous DSL and transmission and single line telephone service. POTS splitters come in two configurations:

    - Single splitter version for mounting at the residence

    - Multiple splitter version for mass termination at the CO

    POTS splitters are either passive or active. Active splitters require an external power source, and passive splitters require no power and often have a higher mean time between failure (MTBF) than the active splitter. Passive splitters enable lifeline services, such as 911, in the event of a DSLAM or xTU-R power loss; active splitters require backup power.

ADSL Data Rates

Downstream bandwidth depends on a number of factors:

  • Length of the copper line

  • Wire gauge of the copper line

  • Presence of bridged taps

  • Presence of cross-coupled interference

NOTE

Bridged taps are any cable pair spliced into the main pair. Many unused bridged taps remain from the early days when party lines were the norm and two or more taps were made on every line. Bridged taps cause undesirable reflection that can distort the high-frequency signals in modern transmission technologies.

Line attenuation increases with line length and frequency, and decreases as wire diameter increases. Ignoring bridged taps, ADSL performs as shown in Table 7-1.

Table 7-1. ADSL Rates (Ignoring Bridged Taps)

Rate (Mbps)

Wire Gauge (AWG)

Distance (feet)

Wire Size (mm)

Distance (km)

1.5 or 2

24

18,000

0.5

5.5

1.5 or 2

26

15,000

0.4

4.6

6.1

24

12,000

0.5

3.7

6.1

26

9000

0.4

2.7

Customer sites beyond the previously listed distances can be reached with fiber-based digital loop carrier (DLC) systems, as illustrated in Figure 7-4.

Figure 7-4. ADSL with and Without Fiber-based DLC

graphics/07fig04.gif

NOTE

xDSL service will not work over fiber-to-the-curb (FTTC) implementations. FTTC is the installation of optical fiber to within a thousand feet of the home or office. Fiber-to-the-home (FTTH) is the installation of optical fiber from the carrier directly into the home or office.

ADSL Standards and Associations

The American National Standards Institute (ANSI) Working Group T1E1.4 approved an ADSL standard at rates up to 6.1 Mbps (DMT/ANSI Standard T1.413). The European Technical Standards Institute (ETSI) contributed an annex to T1.413 reflecting European requirements including a single terminal interface at the premise side of the access circuit.

The ATM Forum and the Digital Audio-Visual Council (DAVIC) have both recognized ADSL as a physical layer transmission protocol for unshielded twisted pair (UTP) media.

NOTE

UTP is a popular type of cable consisting of two unshielded wires twisted around each other. Because UTP cabling is cost efficient, it is used extensively for local-area networks (LANs) and telephone connections. UTP cabling does not offer the high bandwidth or protection from interference that is found with coaxial or fiber optic cables; however, UTP is less expensive and easier to work with than coaxial or fiber-optic.

Other xDSL Technologies

There are several xDSL implementations in addition to ADSL. These are as follows:

  • Single-lined digital subscriber line (SDSL) A rate-adaptive version of Hi-speed digital subscriber line (HDSL) which like HDSL is symmetric. SDSL enables equal bandwidth downstream from a network service provider CO to the customer site as upstream from the customer site to the CO. SDSL supports data only (maximum of 1.544 Mbps) on a single line and does not support analog calls.

  • High-data-rate digital subscriber line (HDSL) Developed by Bellcore, high bit-rate DSL (HDSL)/T1/E1 technologies have been standardized by ANSI in the United States and by ETSI in Europe. HDSL is a more cost-efficient method of installing T1 service to a customer site than traditional dedicated DS1 service.

  • HDSL 2 Standard enabling symmetric service at T1 speeds using a single-wire pair rather than the two pairs of HDSL service. HDSL-2 also was developed as a standard by which different vendors' equipment can interoperate.

  • G.SHDSL (ITU HDSL Standard) A standards-based, multirate version of HDSL-2, which offers symmetrical service.

  • Integrated services digital network (ISDN) digital subscriber line (IDSL) A cross between ISDN and xDSL, using a single-wire pair to transmit full-duplex data at 128 kbps.

  • Very-high-data-rate digital subscriber line (VDSL) Transmits high-speed data over short reaches of twisted-pair copper telephone lines, with a range of speeds depending on actual line length. The maximum downstream rate under consideration is between 51 and 55 Mbps over lines up to 1000 feet (300 m). Downstream speeds as low as 13 Mbps over lengths beyond 4000 feet (1500 m) also are in consideration.



Network Sales and Services Handbook
Network Sales and Services Handbook (Cisco Press Networking Technology)
ISBN: 1587050900
EAN: 2147483647
Year: 2005
Pages: 269

flylib.com © 2008-2017.
If you may any questions please contact us: flylib@qtcs.net