Coaxial Cable

Coaxial Cable

The second transmission medium to be introduced was coaxial cable (often called coax), which began being deployed in telephony networks around the mid-1920s. Figure 3.2 shows the components of coax. In the center of a coaxial cable is a copper wire that acts as the conductor, where the information travels. The copper wire in coax is thicker than that in twisted-pair, and it's also unaffected by surrounding wires that contribute to EMI, so it can provide a higher transmission rate than twisted-pair. The center conductor is surrounded by plastic insulation, which helps filter out extraneous interference. The insulation is covered by the return path, which is usually braided-copper shielding or aluminum foil-type covering. Outer jackets form a protective outer covering for coax; how many outer jackets there are and what type they are depend on the intended use of the cable (for example, whether the cable is meant to be strung in the air or underground, whether rodent protection is required).

Figure 3.2. Coaxial cable

graphics/03fig02.gif

Characteristics of Coaxial

Coax affords a great deal more frequency spectrum than does twisted-pair. Traditional coaxial cable networks generally support 370MHz. Newer deployments, such as hybrid fiber coax (HFC) architectures, support 750MHz or 1,000MHz systems. (HFC is discussed in detail in Chapter 13.) Therefore, coax provides from 370 to 1,000 times more capacity than single twisted-pair. With this additional capacity, you can carve out individual channels, which makes coax a broadband facility. Multiplexing techniques can be applied to coax to derive multiple channels. Coax offers slightly better performance than twisted-pair, because the metallic shielding protects the center conductor from outside interferences; hence the performance of coax is on the order of 10 9 (that is, 1 in 1 billion) bps received in error. Amplifiers need to be spaced every 1.5 miles (2.5 kilometers), which is another improvement over twisted-pair, but it still means you need a substantial number of amplifiers deployed throughout the network.

Cable TV operators, like the telephony network providers, have been prevalent users of coax, but in the past decade they have been reengineering their backbone networks so that they are fiber based, thereby eliminating many amplifiers and subsequently improving performance. Remember from Chapter 2, "Telecommunications Technology Fundamentals," that amplifiers accumulate noise over a distance. So, in a large franchise area for a cable TV operator, as you get toward the outer fringes, greater noise accumulates and a lower service level is provided than is provided to some of the neighbors upstream. By reengineering their backbones to be fiber based, cable providers can also limit how many amplifiers have to be deployed.

One problem with coax has to do with the deployment architecture. Coaxial cable and HFC architectures are deployed in bus topologies. In a bus topology, the bandwidth is shared, which means congestion levels increase as more users in the neighborhood avail themselves of these features and services. A bus topology also presents security risks. It's sort of like going back to the party line in telephony. You do not have your own dedicated twisted-pair that's yours and only yours. Instead, several channels are devoted to accommodating voice telephony and are shared by everyone in the neighborhood, which makes encryption important. Also, there are some problems with noise in bus topologies. The points where the coax connects into set-top boxes or cable-ready TV sets tend to collect noise, so the cable tends to pick up extraneous noise from vacuum cleaners or hair dryers or passing motorcycles. Thus, if every household on the network is running a hair dryer at 6:30 am, the upstream paths are subjected to this noise, with the result that there will be some performance degradations. (Bus topologies are discussed in more detail in Chapter 8, "Local Area Networking.")

Applications of Coaxial

In the mid-1920s, coax was applied to telephony networks as interoffice trunks. Rather than having to add more copper cable bundles with 1,500 or 3,000 pairs of copper wires in them, you could displace those big cables (which are very difficult to install cost-effectively) with a much smaller coaxial cable.

The next major use of coax in telecom occurred in the 1950s, when it was deployed as submarine cable to carry international traffic. Then it was also introduced into the data processing realm in the mid- to late 1960s. Early computer architectures required coax as the media type from the terminal to the host. LANs were predominantly based on coax from 1980 to about 1987.

Coax has also been used in community antenna TV (CATV, or cable TV) and in the local loop, in the form of HFC architectures. In HFC, you bring fiber as close as possible to the neighborhood; then on a neighborhood node, you terminate that fiber, and from that node you fan the coax out to the home service by that particular node. (This is described in detail in Chapter 13.)

Advantages and Disadvantages of Coaxial

The advantages of coax include the following:

         Broadband system On coax there is a sufficient frequency range to support multiple channels, which allows for much greater throughput.

         Greater channel capacity Each of the multiple channels offers substantial capacity. The capacity depends on where you are in the world. In the North American system, each channel in the cable television system is 6MHz wide (according to the National Television Systems Committee [NTSC] standard). In Europe, with the Phase Alternate Line (PAL) standard, the channels are 8MHz wide. Within one of these channels, you can provision high-speed Internet access that's how cable modems operate. But remember that one channel now is being shared by everybody who is using that coax from that neighborhood node, and that can range from 200 to 2,000 homes.

         Greater bandwidth With coax, you have greater bandwidth systemwide, and you also have greater bandwidth for each channel. Because you have greater bandwidth per channel, you can support a mixed range of services. Voice, data, and even video and multimedia can benefit from the enhanced capacity.

         Lower error rates Because of its insulation, coax has lower error rates and therefore slightly better performance than twisted-pair. The error rate is generally 10 9 (that is, 1 in 1 billion) bps.

         Greater spacing between amplifiers Coax's cable shielding reduces noise and crosstalk, which means amplifiers can be spaced farther apart than with twisted-pair.

The main disadvantages of coax are as follows:

         Problems with the deployment architecture The bus topology in which coax is deployed is susceptible to congestion, noise, and security risks.

         Bidirectional upgrade required In countries in which there is a history of CATV, these cable systems were designed for broadcasting, not interactive communications. So, before they can offer to the subscriber any form of two-way services, those networks have to be upgraded to bidirectional systems.

         Great noise The return path has some noise problems, so you have to deploy added intelligence into the end equipment to ensure that error control is being taken care of.

         High installation costs Installation costs in the local environment are high.

         High costs for local moves, adds, and changes You can't easily do away with the termination of a coax cable. You basically have to pull in a whole new cable to a new locale; it's not a simple modular plug environment.

         Susceptible to damage from lightening strikes Coax is susceptible to damage from lightening strikes, so if you live in an area with a lot of lightening strikes, you must be wary because if that lightening is conducted by your coax, it could very well fry the equipment at the end of it.

 



Telecommunications Essentials
Telecommunications Essentials: The Complete Global Source for Communications Fundamentals, Data Networking and the Internet, and Next-Generation Networks
ISBN: 0201760320
EAN: 2147483647
Year: 2005
Pages: 84

flylib.com © 2008-2017.
If you may any questions please contact us: flylib@qtcs.net